Galloping Naartjie

Boardrider prints

Custom boardrider prints add personality, sponsor-style branding or display graphics to surfboards, kite boards and skateboards. We produce durable printed vinyl for local use in Durban and across KwaZulu-Natal, with guidance on fit, finish and application.

a surfboard blank on padded stands in a shaping bay, printed artwork sheet being positioned carefully by a board builder

What boardrider prints are

Boardrider prints are custom graphics made to fit the shape and use of a board. They are commonly applied to surfboards, kite boards and skateboards for promotional use, event visuals, shop display, team identification or personal styling. The print is produced on self-adhesive vinyl, then trimmed and applied to selected areas or across a larger section depending on the board profile and the finish required.

These graphics work well where you want clear colour, logos, patterns or photo-based artwork on a smooth board surface. On boards used in coastal conditions around Durban, the right material choice matters because sun, salt and regular wiping can quickly show up weak print or poorly bonded edges. We keep the job practical and will advise if a partial panel, nose section, tail section or smaller decal set is the better option.

Board types, sizes and working limits

Each board has its own shape, rocker and surface finish, so there is no single size that suits every job. For enquiry purposes, send the overall board length and widest point in millimetres, plus clear photos of the top and underside. If the board has channels, heavy curvature, deep texture or existing damage, tell us upfront so we can check what is realistic.

  • Surfboards: suited to logo panels, tail graphics, deck accents and larger display wraps on smooth, sound surfaces.
  • Kite boards: suited to paired graphics, rider ID, event branding and underside prints where the board face is even.
  • Skateboards: suited to underside graphic panels and cut vinyl details on clean sealed decks.
  • Longboards and mini cruisers: possible for printed panels, but truck positions and deck hardware must be considered.

Working limits usually come from compound curves, waxed surfaces, chipped rails and porous finishes. A very curved nose or rail can require the design to be broken into sections rather than one full piece. Boards with fresh repairs may need extra curing time before any graphic is applied, and boards that are heavily used in surf may need more frequent edge checks after fitting. If a full wrap will not last properly we will say so, rather than pushing a job that won't hold up.

Where boardrider prints suit best

These prints suit promo boards, showroom displays, event boards, prize items, retail decoration and personal boards that need a specific look. They are useful when you want a short-run custom finish without repainting the board. Shops and clubs often use them for launch events, demo days and indoor displays because the artwork can be bright, neat and easy to repeat across several boards.

They are less suitable on rough unfinished timber, heavily sanded foam, damaged laminate, waxed decks that cannot be fully cleaned, or boards that are constantly dragged on roof racks and launch areas. For boards in hard daily surf use, smaller graphics placed away from rail edges and impact zones are often the smarter choice. That tends to give cleaner long-term results, even if the board gets rinsed and handled often.

  • Good fit: retail displays, event activations, team boards, launch promos, gifts and club branding.
  • Less suitable: badly chipped boards, loose laminate, damp repairs, very textured surfaces and unclean wax-heavy decks.
  • Best local use: indoor displays, occasional water use, promo shoots and managed fleet or rental boards.

Artwork, print finish and installation needs

Clean artwork makes a big difference on a board because shapes taper and any poor file setup is easy to spot. Vector logos are best for names, badges and sponsor-style marks. Photos and complex artwork should be supplied at high resolution at full size where possible. If your design must line up to fins, traction areas or hardware, mark those positions clearly in the images you send us.

Installation is normally done on a clean, dry board surface free from wax, polish, salt build-up and loose residue. Boards need to be brought in dry and at a steady temperature, especially in humid coastal weather where trapped moisture can affect adhesion. Freshly waxed or recently cleaned boards with oily products are not ready for application. If a graphic is being fitted over an older decal area, there may be ghosting or a visible paint difference once the old material comes off.

  • Provide top and underside photos in good light.
  • Give board length, width and any key measurements around the print area.
  • Note fin boxes, traction pads, leash points and repairs.
  • Tell us if the board is for display only or regular use in water.

Care and expected wear

Printed vinyl is durable, but a board is still a high-contact item. Salt, UV, sand, knocks and repeated rinsing all affect service life over time. After application, allow the graphic to settle before heavy handling or water exposure. Gentle cleaning with fresh water and a soft cloth is usually enough. Avoid harsh solvents, abrasive pads and high-pressure washing close to the edges.

If the board is stored on roof racks, dragged tail-first, or knocked in transport, edge wear can happen sooner. On skateboards, scrape contact and repeated curb impact will mark printed areas quickly. This is normal wear rather than a print fault. For indoor display boards the finish generally stays cleaner for longer, and colour remains more even if kept out of direct harsh sun all day. A little care goes a long way here.

What to include in your enquiry

Use the contact form and give us enough detail to quote the right option first time. If you are ordering several boards for a shop, event or club, list each type separately and note whether the artwork repeats or changes from board to board. We can then advise on the practical route for print, trim and fitting.

  • Board type: surfboard, kite board, skateboard or other.
  • Overall size in millimetres and the approximate print area.
  • Photos of the board top, underside and any damaged areas.
  • Whether you want a small logo set, partial graphic or large coverage.
  • Artwork files, or a note on whether artwork still needs to be prepared.
  • Intended use: display, promo, gift, event or regular riding.
  • Your town in KwaZulu-Natal and whether fitting is needed.

If you are not sure what will suit the board, send the photos and the use case first. We will point you to the option that makes sense for the shape and surface, without overcomplicating it.

What our Printing and Signage customers say

Verified Google reviews

Questions we get asked

Can you print a full surfboard wrap?

Sometimes, yes, but it depends on the board shape, rail curve, surface condition and intended use. In many cases a partial wrap or panel graphic gives a cleaner result and lasts better.

Will the print survive in the sea?

It can handle occasional water use when applied properly to a suitable surface, but salt, sun, knocks and handling will shorten its life. For hard daily surf use, smaller graphics are often the better option.

What if my board already has old stickers or damaged areas?

Tell us before we quote. Old adhesive marks, faded patches, chips and repairs can affect adhesion and finish, and some areas may need to be avoided.

Ask for a quote

Use the contact form to tell us what you want printed, where it will be used and whether fitting is needed, and Galloping Naartjie will reply with a quote.

Open the contact form